IC693CPU364RR | 單插座CPU | IC693CPU313RR | IC693CPU323CA
產品描述
IC693CPU364RR它是一個單插座CPU(來自GE Fanuc系列90-30)，帶有嵌入式以太網電纜和內置串行端口。該單元是PLC的“大腦”，是大多數計算發生的地方。具體規格請參見IC693CPU364官網。IC693CPU364RR的標準應用是將計算機的9針串口通過IC693CPU364RR連接到IC693CPU364的標準以太網接口上。IC693CPU364RR的以太網接口為EGD (Ethernet Global Data)接口。這種內置以太網接口的好處是，您不需要在設備上使用單獨的以太網模塊，例如CMM321。實際上，您可以根據IC693CPU364以太網端口的內置特性來節省PLC插槽。
EGD還允許CPU364處理HHP配置模式不能處理的特殊參數。與CMM321不同，CPU364不需要外接收發模塊。CPU364內置收發器，可通過10BASE-T接口連接。然而，CPU364確實提供了一些額外的功能，允許您添加外部收發器。這可以通過繞過內部收發器的AAUI端口來實現。內置以太網接口的另一個好處是，它可以在不使用PLC背板的情況下進行通信，從而產生比單獨的CPU和以太網模塊更快的通信速度。關于IC693CPU364的一些基本注意事項是，在使用CPU364時，必須在其所在槽位連接到機架接地。您可以在設備上找到接地線。
CPU364采用flash固件標準，無EPROM和EEPROM。IC693CPU364額定電流為1A，采用GE Fanuc保險絲44A725214-001。CPU364的最大CPU容量為2個
具體來說，PLC CPU的主要功能包括:
編程接受并存儲來自程序員的用戶程序和數據輸入，并可以進行修改或更新。
從現場輸入的用戶程序和數據通過掃描接受并存儲在輸入狀態表(即輸入繼電器)和數據寄存器(即所謂輸入圖像寄存器)中。
從存儲器中逐條讀取用戶程序，通過解釋用戶邏輯完成用戶程序中指定的各種任務，并更新輸出映像寄存器的內容。
輸出控制是根據電路存儲在輸出中的內容來實現的。
Product description
IC693CPU364RR
It is a single socket CPU(from GE Fanuc Series 90-30) with an embedded Ethernet cable and a built-in serial port. This unit is the "brain" of the PLC and is where most calculations take place. For details, see IC693CPU364 official website. The standard application of IC693CPU364RR is to connect the 9-pin serial port of the computer to the standard Ethernet interface of IC693CPU364 through IC693CPU364RR. The IC693CPU364RR uses an Ethernet Global Data (EGD) interface. The benefit of this built-in Ethernet interface is that you do not need to use a separate Ethernet module on your device, such as the CMM321. In fact, you can save PLC slots based on the built-in features of the IC693CPU364 Ethernet port.
EGD also allows the CPU364 to handle special parameters that the HHP configuration mode cannot handle. Unlike the CMM321, the CPU364 does not require an external transceiver module. The CPU364 has a built-in transceiver that can be connected via a 10BASE-T interface. However, the CPU364 does offer some additional features that allow you to add external transceivers. This can be done by bypassing the AAUI port of the internal transceiver. Another benefit of the built-in Ethernet interface is that it can communicate without the use of a PLC backplane, resulting in faster communication speeds than a separate CPU and Ethernet module. Some basic considerations about the IC693CPU364 are that when using the CPU364, it must be connected to the rack ground in its slot. You can find the ground cable on the device.
The CPU364 adopts the flash firmware standard without EPROM or EEPROM. The IC693CPU364 is rated at 1A and uses GE Fanuc fuse 44A725214-001. The CPU364 supports a maximum of two cpus
Specifically, the main functions of the PLC CPU include:
Programming accepts and stores user program and data input from the programmer and can be modified or updated.
User programs and data input from the field are accepted by scanning and stored in the input status table (i.e. input relay) and data register (i.e. so-called input image register).
Read the user program from the memory one by one, complete various tasks specified in the user program by interpreting the user logic, and update the contents of the output image register.
The output control is implemented based on what the circuit stores in the output. Perform various diagnostics product descriptions
